Skip to content
Honed aggregate pool surround in Perth, the polished stone face running flush along the edge of a clear blue pool.

Honed Aggregate Pool Surrounds

A polished, stone-faced surround that runs flush to the coping, hides the skimmer lid and sheds water the right way from day one.

What is a honed aggregate pool surround?

A honed aggregate pool surround is concrete that is ground back after curing to cut the stone flat, giving a smooth, low-glare, terrazzo-like finish. It is sealed for slip resistance and easy cleaning. In Perth, Elite Scape Solutions installs them with seamless edges, flush infilled skimmer lids and falls planned before the pour.

Honed aggregate is concrete that has been ground back after it cures, cutting the stone in the mix flat so you see a smooth, terrazzo-like face. It is cooler and calmer to look at than a broom finish, far more refined than exposed aggregate, and it does not move or sink like pavers.

Around a pool it has to do more than look good. It is exposed to pool-water splashes, full sun and constant foot traffic, with a shell, skimmer and fence spigots in the middle of it. That is why we treat the surround as its own specialist job, not something a general concreter squeezes in after the pool goes in.

Compare pool surround options
A smooth honed aggregate edge following the curve of a blue pool.

Why it matters

  • It is the bit you walk on every day

    The pool gets the budget and the attention. The surround is what you see from the kitchen and feel under your feet all summer.

  • Water has to go somewhere

    Poor falls mean pooling, staining and slippery edges by the first summer. We plan drainage first, not last.

  • One finish, start to end

    Steps, edges, lids and alfresco in the same mix, so the whole space ties together instead of looking patched.

Project photos

View all projects
  • Honed aggregate pool surround in Perth, the polished stone face running flush along the edge of a clear blue pool.
    Honed aggregate pool surround in Perth, the polished stone face running flush along the edge of a clear blue pool.
  • A smooth honed aggregate edge following the curve of a blue pool.
    A smooth honed aggregate edge following the curve of a blue pool.
  • Close-up of the flat-cut stone face in a honed aggregate surface.
    Close-up of the flat-cut stone face in a honed aggregate surface.
  • Honed aggregate flooring beneath a covered alfresco beside the house.
    Honed aggregate flooring beneath a covered alfresco beside the house.
  • Honed aggregate path running between the house and boundary fence.
    Honed aggregate path running between the house and boundary fence.
  • Skimmer lid infilled with matching honed aggregate so it sits flush and almost disappears into the surround.
    Skimmer lid infilled with matching honed aggregate so it sits flush and almost disappears into the surround.

The process

How it works

  1. 01

    Send us your plans

    Upload pool plans, site plans or a few photos of the space with your enquiry.

  2. 02

    Free on-site measure

    We measure, check levels and drainage, and talk through finishes and options.

  3. 03

    Fixed written quote

    A clear, itemised quote with real dates. No allowances that blow out later.

  4. 04

    Construction

    We schedule the work around your pool handover, complete the job and leave the site clean.

Common questions

What's the difference between honed aggregate and exposed aggregate?

Same concrete, two ways of revealing the stone in it. Exposed aggregate is washed back while the slab is still green, leaving a textured, pebbly surface with plenty of grip. Honed aggregate is ground back mechanically once the slab has cured, cutting the stone flat for a smooth, low-glare, stone-faced finish. Honed is the more premium of the two and what most people mean by a premium pool surround.

Is honed aggregate slippery around a pool?

Not when it is finished properly. Our standard-grit hone leaves a smooth face with enough texture for wet areas, we seal with a product rated for wet areas and can add a fine anti-slip additive to the sealer. Correct falls matter just as much, because standing water is what makes any surface slippery.

Do I need the pool finished before you start?

For a fibreglass pool, yes: it needs to be installed and finished first. For a concrete pool it is usually the other way round, with the surround done before the pool is surfaced because honing makes the water dirty. Send us your plans and we will sort the order out with your pool builder.

How long does a honed aggregate pool surround take?

The pour is the quick part. Set-out, formwork, drainage and prep are the bulk of the work, then the slab must cure before it can be honed and sealed. Timing depends on the area, weather and site prep, and you get real dates with the quote.

Does honed aggregate get hot in the Perth sun?

All concrete warms up in full sun, but colour makes the biggest difference. Light, white and pale-grey honed mixes stay noticeably cooler underfoot than dark or charcoal mixes. If heat matters to you, choose a light cement colour and light stone, and we will talk you through the options at the measure.

How do I maintain a honed aggregate pool surround?

Sweep or hose it down regularly and rinse off pool chemicals and leaf stains. The sealer is what protects it, so plan to reseal every few years depending on sun exposure and wear. We give you care instructions at handover.

What affects the cost of a honed aggregate pool surround?

The main factors are the area in square metres, site access, how much excavation and base preparation is needed, drainage, the number of steps and skimmer lids, and the stone mix. That is why we measure on site before giving a fixed written price.